Water Heater Settings When You Leave a Florida Home for Weeks
A water heater that keeps a full tank hot all summer is one of the quiet energy wastes in an empty Florida house — and a tank sitting warm with no one using the taps is also a place germs can hang around. Here's what FPL, UF/IFAS, the CDC and ENERGY STAR say about leaving a tank or tankless unit for weeks or months.
Turn off the water heater before vacation? Tank heaters: off vs lowest setting
FPL's energy-saving tips for seasonal residents lists "turn off your water heater at the circuit breaker" among its seasonal-resident appliance tips. FPL's 2026 snowbird checklist (via WUSF) repeats it: shut off water heaters at the breaker (and turn off the main water valve unless a fire-sprinkler system needs it on). UF/IFAS Extension's "Closing Your Seasonal Home" is more nuanced by trip length: turn the water heater off if you'll be gone more than a month; for shorter absences, turn power off, set the thermostat to its lowest setting, then restore power per the unit's instructions.
For gas heaters, follow the manufacturer's vacation or pilot instructions rather than improvising. Our guide on whether to shut off the water when you leave covers the order of operations: water heater first, then the main, unless fire sprinklers or irrigation change the plan.
Tankless water heaters
ENERGY STAR explains that whole-home tankless (demand) water heaters heat water only when a tap is opened, which eliminates the standby energy a storage tank loses keeping water hot all day. With no one home and no hot-water draws, that standby load simply isn't there. Still check your manual for:
- Any vacation or standby setting the maker provides
- Recirculation pumps or schedules — those can waste energy if they keep looping hot water through empty pipes
- Freeze protection on outdoor or attic units (rare for Martin County winters, but follow the manual if your model needs power left on for it)
Temperature, Legionella and scald risk
the CDC's guidance on preventing waterborne germs at home says keeping a home water heater between 130°F and 140°F can kill germs like Legionella in the water, but hotter water increases burn risk. If you set the heater above 120°F, use thermostatic mixing valves at the tap. The CDC also says to ask your healthcare provider whether a higher setting is appropriate for your risk. Separately, the U.S. Department of Energy's Home Energy Checklist lists turning the water heater down to the warm setting (120°F) as an everyday energy step that also reduces scalding — that everyday tip is not the same as FPL's "turn it off while vacant" advice; use off/lowest for long vacancies, then restore a safe operating temperature when you return.
Stagnant pipes matter too. The CDC notes germs can grow when water sits still, such as when taps go unused for a week or longer, and recommends flushing unused faucets and showerheads before you use them again.
Drain pans and leak risk
A tank heater can drip for days into a pan or onto a garage or closet floor before anyone notices — worse when the house is empty. Before you leave:
- Look at the drain pan, the area around the tank and the T&P discharge line for moisture or rust.
- Place a leak sensor in the pan or on the floor beside the tank.
- Know where the main shutoff is if a sensor alert comes in.
Our Smart Protection Kit ($249) includes YoLink leak and freeze sensors for whole homes. Condos and apartments that mainly need under-sink and water-heater coverage can start with the Condo Leak Starter Kit ($169). Both ship anywhere in the U.S. and have no monthly fee for the sensors themselves.
When you come back
- Restore power (or the gas pilot) per the manufacturer's steps.
- Set a temperature that matches your household's scald and Legionella discussion with a clinician or plumber.
- Flush faucets and showers the CDC way: cold fully for about 2 minutes, then hot until it feels hot.
- Consider a manufacturer-recommended tank flush after a long sit, or hire a plumber if you're not comfortable draining it.
Pair the heater decision with a real check
Sensors catch water on the floor. Someone inside the house can see a wet ceiling, a tripped breaker or a pan that overflowed overnight. Martin County home watch plans start at $89 a month with a dated photo report after every visit. A water heater check is part of what a visit includes.
Hear about a water heater leak the same day
YoLink leak sensors with phone alerts. No monthly sensor fee. Ships anywhere in the U.S.
Buy the Smart Protection Kit, $249Sources: FPL's energy-saving tips for seasonal residents; FPL's 2026 snowbird checklist (via WUSF); UF/IFAS Extension's "Closing Your Seasonal Home"; the CDC's guidance on preventing waterborne germs at home; ENERGY STAR; the U.S. Department of Energy's Home Energy Checklist. This page is general information, not plumbing, medical or energy advice for your specific equipment — follow your water heater's manual and local codes.
Common questions
Should I turn off my water heater when I leave Florida for weeks? FPL tells seasonal residents to turn the water heater off at the circuit breaker so it isn't holding hot water nobody will use. UF/IFAS says turn it off if you'll be gone more than a month; for shorter trips, set it to the lowest setting after cutting power to change the thermostat.
What about a tankless water heater? Tankless units heat water only when a tap calls for it. ENERGY STAR explains that they save energy by eliminating standby tank losses. With no hot-water use while you're away, they draw little; still follow your unit's manual for vacation mode, recirculation pumps and freeze protection if your model has them.
What temperature does the CDC recommend for Legionella? The CDC says keeping a home water heater between 130°F and 140°F can kill germs like Legionella, but hotter water raises scald risk. If you set above 120°F, use thermostatic mixing valves at taps. Ask your healthcare provider whether a higher setting is right for your household.
What should I do when I return after weeks away? The CDC recommends flushing faucets and showerheads that sat unused for a week or more: run cold fully for about 2 minutes, then hot until it feels hot. Many manufacturers also recommend flushing the water heater after long absences — follow the unit's instructions or hire a plumber.
Where do water heater leaks show up first? Usually in the drain pan under a tank heater, around the T&P valve discharge, or on the floor nearby. Put a leak sensor in the pan or on the floor beside the tank, and have someone look inside on a schedule. Our Smart Protection Kit and Condo Leak Starter Kit both include YoLink leak sensors for that job.